America's #1 Direct Source for Pool Supplies!

1.800.288.7946 Experts Available 24/7

Menu
Call Cart
one day delivery

1 Day Delivery

Your ZIP Code: 06828 Fairfield Change Location

To Fairfield Change
Celebrating 35+ Years!
Source / Promo Code:WYAARUNKEdit
cart overlay

    Showing 0 of 0 item View All

    Estimated SUBTOTAL* :  $0.00

    *Excludes taxes, handling fee, and EZ Pay Service Fee, if applicable.
    Source Code:WYAARUNK Edit
    Winter Cover Sale!
    save 10% OFF! Our Most Popular Winter covers!
    Save 10% OFF! Our Most Popular Winter Covers!
    BUY NOW and be ready for this season's end! Shop Now!

    Hayward Super Pump Replacement Motors

    Keep Your Pool Running With A Hayward Super Pump Replacement Motor

    The Hayward Super Pump replacement motor is the ideal way to save money and keep your pool pump running. The Hayward replacement motor bolts right on to the existing Super Pump wet end housing, saving you a lot of time and expense from having to buy a completely new pump.

    The replacement motor is simple to install and wire, and there’s no re-plumbing needed. You can wire the motor for 115/230 volts, and the Hayward Super Pump replacement motor comes in ¾ to 2 horsepower sizes.

    • Threaded shaft, C-flange, 56 frame, up-rated
    • See our Rebuild Kits below when replacing a Hayward Super Pump motor
    • Hayward replacement motor bolts right on to Hayward Super Pump; no need for re-plumbing
    • See also our genuine OEM Hayward Superpump motors
    • Reversible Voltage Connects to either 115V or 230V
    • 1 Year Hayward warranty

     

    ***PLEASE NOTE: SOME POOL PUMP MOTORS CANNOT BE SHIPPED TO CALIFORNIA. To view Title 20 California Code of Regulations, visit the California Appliance Efficiency Database.***

    read more
      • Item: # E0128 .95 THP Motor C-Flange 56J $149.99
        Direct replacment for 3/4 HP up-rated or 1/2 HP full-rated motors.
      • Item: # E0126 1.25 THP Motor C-Flange 56J $164.99
        Direct replacment for 1 HP up-rated or 3/4 HP full-rated motors.
      • Item: # E0135 1.65 THP Motor C-Flange 56J $184.99
        Direct replacment for 1.5 HP up-rated or 1 HP full-rated motors.
      • Product Description
      • Customer Review

      REPLACING A HAYWARD SUPERPUMP MOTOR

      To replace your Hayward Superpump motor, shut off all power, and remove the four hex-head bolts that connect the seal plate to the pump housing. Slide the motor out of the pump housing. Remove the rear motor cover and remove the two power wires and the ground wire from your existing motor, and the flexible conduit connector. 

      At the rear of the motor, loosen the thermal regulator (12 o'clock) or the capacitor (9 o'clock), to allow access to the rear of the shaft. Insert a 7/16" open end wrench on the slotted end of the motor shaft to hold it stationary, while on the other end of the Superpump motor, twist the impeller off in a CC direction. Use large channel pliers if necessary, covering the impeller with a soft cloth to prevent damage. 

      When the impeller is removed, remove the seal plate and the four bolts holding the motor mounting plate to the old motor. Reattach the motor mounting plate to the new motor, and press fit the round half of a NEW shaft seal into the seal plate, taking care to keep it clean and free of oils. Place the other spring half of the new shaft seal onto the back of the impeller, taking care to install in the proper direction (soft rubber side toward impeller, hard plastic side toward motor).

      Check that the motor is set to accept the proper voltage (115V or 230V), and rewire the new motor in the same manner as the old motor. Spin impeller back onto the shaft, and install diffuser (and diffuser gasket) over the impeller. Slide the motor assembly into pump and tighten the four bolts, with the housing gasket properly positioned. Tighten the four bolts to secure the motor into the pump housing. Fill with water, seal pump lid and turn on power to motor.