Delivery To Ashburn Edit
*Shipping is FREE for all orders in the 48 contiguous states, except for a handling charge.
The oversized Hayward X-Stream pool filter won’t clog as it works to keep your pool water crystal clear. An industrial sized strainer basket and wide openings collect more debris, including larger items like leaves, reducing your pool maintenance time. The included Hayward Power-Flo Matrix pool pump creates a lot of suction power, which is great if you have a pool vacuum that uses the pool filter.read more
Cartridge filters for swimming pools are easier to maintain than other types of filters, like D.E. and sand, plus there’s no need to backwash a cartridge filter. An Easy-Lok ring design on the Hayward X-Stream above ground pool cartridge system gives you quick access to the filter so you can clean it with a garden hose once or twice a season.
– Dirt, debris, or tear in pleats or folds
– Clean or replace element
– Braking of internal core of the element.
– Breaking or splitting of the end plates of the element.
– Re-size pump.
– Lay the float hose out straight in the sun to remove the coils.
– Manually check rotation of motor shaft for free movement and lack of obstruction.
– If you have a timer, be certain it is working properly. Bypass it if necessary.
– Check for air bubbles around the jet body assembly. This may indicate air in the plumbing lines.
– See "Surface module moves too fast."
– Low voltage at motor or power drop (frequently caused by undersized wiring or extension cord use).
– Mechanical binding and electrical overloads.
NOTE: Your Hayward pump motor is equipped with an "automatic thermal overload protector." The motor will automatically shut off if power supply drops before heat damage can build up causing windings to burn out. The "thermal overload protector" will allow the motor to automatically restart once the motor has cooled, provided the power source is again up to proper levels. It will continue to cut On/Off until the problem is corrected. Be sure to correct cause of overheating.
– Binding of motor shaft.
– Block off to determine if pump will develop a vacuum. You should have 5"-6" of vacuum at the strainer cover (Only your pool dealer can confirm this with a vacuum gauge). You may be able to check by removing the skimmer basket and holding your hand over the bottom port with skimmer full and pump running. If no suction is felt, check for line blockage.
– If pump develops a vacuum, check for blocked suction line or dirty strainer basket, an air leak in the suction piping may be the cause.
– If pump does not develop a vacuum and pump has sufficient "priming water":
– Re-check strainer housing cover and all threaded connections for suction leaks.Check if all hose clamps are tight.
– Check voltage to ensure that the motor is rotating at full RPM's.
– Open housing cover and check for clogging or obstruction in suction. Check impeller for debris.
– Remove and replace shaft seal only if it is leaking.
– Plugged or restricted discharge line of filter, valve partially closed (high gauge reading). How to correct: Sand filters – backwash as per manufacturer's instructions; D.E. filters – backwash as per manufacturer's instructions; Cartridge filters – clean or replace cartridge.
– Air leak in suction (bubbles issuing from return fittings). Re-tighten using Teflon tape.
– Plugged or restricted impeller or impeller sheared off. Replace including new seal assembly.
– Cavitation due to restricted or undersized suction line or leak at any joint, low water level in pool, and unrestricted discharge return lines. Correct suction condition or throttle return lines, if practical. Holding hand over return fitting will sometimes prove this point or putting in a smaller eyeball fitting.
– Vibration due to improper mounting, etc. Put a rubber pad under metal mounting feet.
– Foreign matter in pump housing. Loose stones/debris hitting impeller could be cause, remove any of the above.
– Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals causing seal damage, which will allow chlorinated water to seep into bearings wiping out the grease causing bearing to whine. All seal leaks should be replaced at once.
– Equipment base vibrating