1.800.288.7946

Delivery To Select Location

FREE SHIPPINGHandling May ApplyDetails Handling May Apply

Menu
Call Cart

    Showing 0 of 0 item View All

    Estimated SUBTOTAL* :  $0.00

    *Excludes taxes, handling fee, and EZ Pay Service Fee, if applicable.
    Source Code:WYAARUNKEdit

    Chlorine Sale! $10 OFF Chlorine & Bromine! Enter Promo Code 99932 at Checkout. Valid only on 25lb+

    10 x 15 ft Oval Pool Overlap Liners

    Item # L1045D

    $174.99

      POOL LINERS AVAILABLE IN 20-GAUGE, 25-GAUGE, & 30-GAUGE SUPER-STRONG VIRGIN VINYL!

      In the Swim's 10 x 15 foot oval overlap pool liners will provide you with outstanding durability as well as attractive style. These above ground overlap pool liners are designed to be secured under your pool's top rail. The fabric of overlap pool liners is draped over the pool's walls and held in place with clips. The top rail is then placed over top of the liner.
      • Our 10 x 15 foot oval overlap pool liners are available in a number of stylish, eye-catching designs including a boulder swirl pattern, an aquarium pattern and a Caribbean pattern. These overlap pool liners are also available in solid blue.
      • Our 20 gauge liners are backed by a 15 year warranty.
      • Our 25 gauge liners are backed by a 25 year warranty.
      • Our 30 gauge liners are backed by a 25 year warranty.
      • Constructed from super-strong virgin vinyl for exceptional durability.
      • Double welded seams for rugged construction and superior resistance against wear and tear.
      • Will resist fading and damage caused by harsh weather and UV radiation from the sun.
      • All flat bottom liners will fit above ground pools with either 48 inch or 52 inch sidewalls
      • Easy to install.
      • Affordably priced.
      read more

      • Product Description
      • Customer Review
      • MORE INFO

      For liner gauge samples, order our Information Packet located below.

      Installation Instructions
      RECOMMENDED ITEMS NEEDED FOR INSTALLTION
      • 2” gray duct tape with non-asphalted adhesive
      • screwdriver
      • garden hose
      • sharp nail or ice pick
      • industrial vacuum or household vacuum (filter bag removed)
      • tamping tool
      • masking tape
      • utility knife







        WARNING: Liner should be stored at room temperature for at least 72 hours prior to installation.

      PREPARATION OF POOL BOTTOM

      1. Spread a 2” layer of brick sand over the entire pool foundation area inside the base rails. Use a rake to make the brick sand flat and smooth. Tamp sand to help reduce footprints. In place of brick sand, you can use “Soft Step” Floor Padding. Cut the sheets to fit and join them with duct tape along the whole length of each seam.

      2. With the brick sand, make a curved cove about 4” high and 4” wide all around the bottom of the pool wall on the inside. Pack firmly into shape. Pool Cove can also be used.


      LINER INSTALLATION

      1. Place the closed liner carton in the center of the pool.

      2. Open the carton. Do NOT use anything sharp to open the carton.

      3. Unfold the liner and spread it out in the sun to warm up.

      4. Inspect all seams and surfaces for holes.

      5. Spread out liner. The curved seam should be centered on the cove at the base of the wall. The other seams will form straight lines across the bottom of the pool. If seams appear to have flaps, check to see if correct side is up.

      6. Smooth out all wrinkles in the bottom.

      7. If you have a beaded liner, fasten the liner in place by lifting the sides of the liner and inserting the beaded edge into the liner retainer on the top edge. If you do not have a beaded liner, lift the sides of the liner and drape them over the top of the pool wall. Fasten liner to the top of the wall with plastic coping. Let the liner hang slack for now. Do NOT pull liner tight.

      8. Start filling the pool with water. As the pool fills, work out the wrinkles and smooth the liner to the wall. Remove the plastic coping around the top edge of the wall one piece at a time and adjust the liner. Keep smoothing out the wrinkles.

      9. Do not install faceplates, inlets, light fixtures, etc. until water reaches 3” below each opening. Premature installation might result in the liner tearing away from the opening due to stretching as the water level increases.

      10. Proceed filling pool until water reaches desired level.


      OPTIONAL STEP TO ELIMINATE WRINKLES

      1. To remove air from behind the liner, which prevents wrinkles, insert a vacuum cleaner hose through the skimmer hole in the pool wall behind the liner. To minimize vacuum loss, seal the opening around the hose and the water inlet using cardboard and masking tape.

      2. Turn vacuum cleaner on. While vacuum is running, you should be adjusting the liner with short tugs to eliminate wrinkles. If you have trouble shifting the liner into position, shut vacuum off for a few minutes. You should then be able to adjust the troubled area before continuing with the vacuum.

      3. Start filling the pool with water. The vacuum cleaner should continue to run until water level nears the top. Make sure to keep vacuum cleaner hose above the water level at all times.
      You May Also Like...
      Warranties